There is what appears to be an active wasp nest/bee hive on the north gable above the garage. No apparent damage to soffit or eaves. Recommend a qualified pest control company evaluate and remove the nest/hive.
Bryan Fujimoto
Reah Latore
The inspection was essentially visual and not technically exhaustive. The inspection was based upon conditions that existed at the time of the inspection. This inspection may have excluded some of the components, items, and/or conditions by nature of their location were concealed or otherwise difficult to inspect. There was no dismantling, destructive analysis, or technical testing of any component. Excluded were all cosmetic conditions, such as floor coverings and wall coverings. The inspection covered only the listed items and was evaluated for function and safety, not code compliance. The inspection covered only the listed items and was evaluated for function and safety, not code compliance. This was not intended to reflect the value of the premises and did not make any representation as to the advisability or inadvisability of purchase. Hypothetical repair costs may have been discussed but must be confirmed by qualified contractor estimates.
THE INSPECTION DID NOT INCLUDE ANALYSIS OR TESTING OF ANY ENVIRONMENTAL HEALTH HAZARDS. No tests were conducted to determine the presence of airborne particles such as asbestos, noxious gases such as radon, formaldehyde, toxic, carcinogenic or malodorous substances or other conditions of air quality that may have been present; nor conditions which may cause the above. No representations were made as to the existence or possible condition of the lead paint, abandoned wells, private sewage systems, or underground fuel storage tanks. There were no representations as to any above or below ground pollutants, contaminants, or hazardous wastes. The quality of drinking water was excluded from this inspection.
THE INSPECTION DID NOT INCLUDE ANALYSIS OR TESTING FOR CONCEALED WOOD DECAY, MOLD, MILDEW OR FUNGI GROWTH.
THE INSPECTION DID NOT INCLUDE ANALYSIS OR TESTING FOR INSECTS AND VERMIN.
THE INSPECTION AND REPORT ARE NOT A GUARANTEE OR WARRANTY, EXPRESSED OR IMPLIED, OF THIS BUILDING OR ANY OF ITS COMPONENTS. The inspection and report are furnished on ‘opinion only’ basis. This company assumes no liability and shall not be liable for any mistakes, omissions, or errors in judgment beyond the cost of this report. We assume no responsibility for the cost of repairing or replacing any unreported defects or conditions. This report is for the sole use of our client and no third party liability is assumed.
IN | NI | NP | O | ||
---|---|---|---|---|---|
2.1 | Foundation, Basement & Crawlspaces | X | |||
2.2 | Roof Structure & Attic | X | |||
2.3 | Ceiling Structure | X | |||
2.4 | Wall Structure | X | |||
2.5 | Floor Structure | X |
3. STRUCTURAL COMPONENTS 3.1 The inspector shall: A. inspect structural components including the foundation and framing. B. describe: 1. the methods used to inspect under floor crawlspaces and attics. 2. the foundation. 3. the floor structure. 4. the wall structure. 5. the ceiling structure. 6. the roof structure. 3.2 The inspector is NOT required to: A. provide engineering or architectural services or analysis. B. offer an opinion about the adequacy of structural systems and components. C. enter under floor crawlspace areas that have less than 24 inches of vertical clearance between components and the ground or that have an access opening smaller than 16 inches by 24 inches. D. traverse attic load-bearing components that are concealed by insulation or by other materials.
IN | NI | NP | O | ||
---|---|---|---|---|---|
3.1 | Walkways, Patios & Driveways | X | |||
3.2 | Vegetation, Grading, Drainage & Retaining Walls | X | |||
3.3 | Siding, Flashing & Trim | X | |||
3.4 | Decks, Balconies, Porches & Steps | X | |||
3.5 | Exterior Doors | X | |||
3.6 | Eaves, Soffits & Fascia | X | X |
4.1 The inspector shall: A. inspect: 1. wall coverings, flashing, and trim. 2. exterior doors. 3. attached and adjacent decks, balconies, stoops, steps, porches, and their associated railings. 4. eaves, soffits, and fascias where accessible from the ground level. 5. vegetation, grading, surface drainage, and retaining walls that are likely to adversely affect the building. 6. adjacent and entryway walkways, patios, and driveways. B. describe wall coverings. 4.2 The inspector is NOT required to inspect: A. screening, shutters, awnings, and similar seasonal accessories. B. fences, boundary walls, and similar structures. C. geological and soil conditions. D. recreational facilities. E. outbuildings other than garages and carports. F. seawalls, break-walls, and docks. G. erosion control and earth stabilization measures.
There is what appears to be an active wasp nest/bee hive on the north gable above the garage. No apparent damage to soffit or eaves. Recommend a qualified pest control company evaluate and remove the nest/hive.
IN | NI | NP | O | ||
---|---|---|---|---|---|
4.1 | Coverings | X | |||
4.2 | Roof Drainage Systems | X | |||
4.3 | Flashings | X | |||
4.4 | Skylights, Chimneys & Roof Penetrations | X |
5.1 The inspector shall: A. inspect: 1. roofing materials. 2. roof drainage systems. 3. flashing. 4. skylights, chimneys, and roof penetrations. B. describe: 1. roofing materials. 2. methods used to inspect the roofing. 5.2 The inspector is NOT required to inspect: A. antennas. B. interiors of vent systems, uses, and chimneys that are not readily accessible. C. other installed accessories.
IN | NI | NP | O | ||
---|---|---|---|---|---|
5.1 | Main Level Cooling Equipment | X | |||
5.2 | Upper Level Cooling Equipment | X | |||
5.3 | Distribution System | X |
If unit is nearing the end of typical service life or has exceeded it, recommend homeowner plan and budget for replacement in the next 5 years.
If unit is nearing the end of typical service life or has exceeded it, recommend homeowner plan and budget for replacement in the next 5 years.
9.1 The inspector shall: A. open readily openable access panels. B. inspect: 1. central and permanently installed cooling equipment. 2. distribution systems. C. describe: 1. energy source(s). 2. cooling systems. 9.2 The inspector is NOT required to: A. inspect electric air cleaning and sanitizing devices. B. determine cooling supply adequacy and distribution balance. C. inspect cooling units that are not permanently installed or that are installed in windows. D. inspect cooling systems using ground source, water source, solar, and renewable energy technologies.
IN | NI | NP | O | ||
---|---|---|---|---|---|
6.1 | Main Level Heating Equipment | X | |||
6.2 | Upper Level Heating Equipment | X | |||
6.3 | Distribution Systems | X | |||
6.4 | Vents, Flues & Chimneys | X |
If unit is nearing the end of typical service life or has exceeded it, recommend homeowner plan and budget for replacement in the next 5 years.
If unit is nearing the end of typical service life or has exceeded it, recommend homeowner plan and budget for replacement in the next 5 years.
8.1 The inspector shall: A. open readily openable access panels. B. inspect: 1. installed heating equipment. 2. vent systems, uses, and chimneys. 3. distribution systems. C. describe: 1. energy source(s). 2. heating systems. 8.2 The inspector is NOT required to: A. inspect: 1. interiors of vent systems, uses, and chimneys that are not readily accessible. 2. heat exchangers. 3. humidifiers and dehumidifiers. 4. electric air cleaning and sanitizing devices. 5. heating systems using ground-source, water-source, solar, and renewable energy technologies. 6. heat-recovery and similar whole-house mechanical ventilation systems. B. determine: 1. heat supply adequacy and distribution balance. 2. the adequacy of combustion air components.
IN | NI | NP | O | ||
---|---|---|---|---|---|
7.1 | Walls, Ceilings, Floors | X | |||
7.2 | Occupant Door (From garage to inside of home) | X | |||
7.3 | Vehicle Door | X | |||
7.4 | Garage Door Opener | X | X |
Door was a proper solid wood or metal door and has seals on bottom which delays spread of fire and limits CO intrusion to interior of home.
Inspection of overhead garage doors typically includes examination for presence, serviceable condition and proper operation of the following components: door condition; mounting brackets; automatic opener; automatic reverse; photo sensor; switch placement; track & rollers; manual disconnect.
The photo-electric sensor designed to activate the automatic-reverse at the overhead garage door responded to testing as designed.
Inspection of the garage typically includes examination of the following:
- general structure;
- floor, wall and ceiling surfaces;
- operation of all accessible conventional doors and door hardware;
- overhead door condition and operation including manual and automatic safety component operation and switch placement;
- proper electrical condition including Ground Fault Circuit Interrupter (GFCI) protection;
- interior and exterior lighting;
- stairs and stairways;
- proper firewall separation from living space;
- proper floor drainage
*Saftey* Modern automatic garage door openers are installed with a pressure sensitive function which will reverse garage door if an object obstructs the path. Too much pressure is needed to reverse the door which can result in harm to pets or persons. This is a safety hazard to children and pets. Recommend pressure sensitivity be adjusted.
IN | NI | NP | O | ||
---|---|---|---|---|---|
8.1 | Fixtures / Faucets | X | X | ||
8.2 | Visible Water Distribution Piping | X | |||
8.3 | Drain, Waste, & Vent Systems | X | |||
8.4 | Water Heater | X | |||
8.5 | Vents, Flues & Chimneys | X | |||
8.6 | Fuel Storage & Distribution Systems | X | |||
8.7 | Sump Pumps / Sewage Ejectors | X |
If unit is nearing the end of typical service life or has exceeded it, recommend homeowner plan and budget for replacement in the next 5 years.
Sump Pumps / Sewage Ejectors not present.
6.1 The inspector shall: A. inspect: 1. interior water supply and distribution systems including fixtures and faucets. 2. interior drain, waste, and vent systems including fixtures. 3. water heating equipment and hot water supply systems. 4. vent systems, flues, and chimneys. 5. fuel storage and fuel distribution systems. 6. sewage ejectors, sump pumps, and related piping. B. describe: 1. interior water supply, drain, waste, and vent piping materials. 2. water heating equipment including energy source(s). 3. location of main water and fuel shut-off valves. 6.2 The inspector is NOT required to: A. inspect: 1. clothes washing machine connections. 2. interiors of vent systems, flues, and chimneys that are not readily accessible. 3. wells, well pumps, and water storage related equipment. 4. water conditioning systems. 5. solar, geothermal, and other renewable energy water heating systems. 6. manual and automatic re-extinguishing and sprinkler systems and landscape irrigation systems. 7. septic and other sewage disposal systems. B. determine: 1. whether water supply and sewage disposal are public or private. 2. water quality. 3. the adequacy of combustion air components. C. measure water supply low and pressure, and well water quantity. D. fill shower pans and fixtures to test for leaks.
Whirlpool tub is leaking at one of the pipes in the pipework on the back of the tub, inside cabinet. Moisture stains also visible below on ceiling in garage. Recommend qualified contractor repair leak.
IN | NI | NP | O | ||
---|---|---|---|---|---|
9.1 | Service Entrance Conductors | X | |||
9.2 | Service and Grounding Equipment, Main Overcurrent Device and Panel | X | |||
9.3 | Branch Circuit Conductors, Overcurrent Devices and Compatibility of Their Amperage & Voltage | X | |||
9.4 | Connected Devices and Fixtures | X | |||
9.5 | Polarity and Grounding of Receptacles | X | |||
9.6 | GFCI & AFCI | X | X | ||
9.7 | Smoke Detectors | X | |||
9.8 | Carbon Monoxide Detectors | X |
Ensure CO Detector remains with home or new one is installed after move in.
7.1 The inspector shall: A. inspect: 1. service drop. 2. service entrance conductors, cables, and raceways. 3. service equipment and main disconnects. 4. service grounding. 5. interior components of service panels and subpanels. 6. conductors. 7. overcurrent protection devices. 8. a representative number of installed lighting fixtures, switches, and receptacles. 9. ground fault circuit interrupters and arc fault circuit interrupters. B. describe: 1. amperage rating of the service. 2. location of main disconnect(s) and subpanels. 3. presence or absence of smoke alarms and carbon monoxide alarms. 4. the predominant branch circuit wiring method. 7.2 The inspector is NOT required to: A. inspect: 1. remote control devices. 2. or test smoke and carbon monoxide alarms, security systems, and other signaling and warning devices. 3. low voltage wiring systems and components. 4. ancillary wiring systems and components not a part of the primary electrical power distribution system. 5. solar, geothermal, wind, and other renewable energy systems. B. measure amperage, voltage, and impedance. C. determine the age and type of smoke alarms and carbon monoxide alarms.
One or more Ground Fault Circuit Interrupter (GFCI) outlets won't "trip" when tested. Recommend a licensed electrician evaluate and repair.
IN | NI | NP | O | ||
---|---|---|---|---|---|
10.1 | Attic Insulation | X | |||
10.2 | Floor Insulation | X | |||
10.3 | Wall Insulation | X | |||
10.4 | Vapor Retarders | X | |||
10.5 | Ventilation | X | |||
10.6 | Exhaust Systems | X |
11.1 The inspector shall: A. inspect: 1. insulation and vapor retarders in unfinished spaces. 2. ventilation of attics and foundation areas. 3. kitchen, bathroom, laundry, and similar exhaust systems. 4. clothes dryer exhaust systems. B. describe: 1. insulation and vapor retarders in unfinished spaces. 2. absence of insulation in unfinished spaces at conditioned surfaces. 11.2 The inspector is NOT required to disturb insulation.
IN | NI | NP | O | ||
---|---|---|---|---|---|
11.1 | Walls | X | |||
11.2 | Ceilings | X | |||
11.3 | Floors | X | |||
11.4 | Steps, Stairways & Railings | X | |||
11.5 | Countertops & Cabinets | X | |||
11.6 | Doors | X | X | ||
11.7 | Windows | X |
10.1 The inspector shall inspect: A. walls, ceilings, and floors. B. steps, stairways, and railings. C. countertops and a representative number of installed cabinets. D. a representative number of doors and windows. E. garage vehicle doors and garage vehicle door operators. F. installed ovens, ranges, surface cooking appliances, microwave ovens, dishwashing machines, and food waste grinders by using normal operating controls to activate the primary function. 10.2 The inspector is NOT required to inspect: A. paint, wallpaper, and other finish treatments. B. floor coverings. C. window treatments. D. coatings on and the hermetic seals between panes of window glass. E. central vacuum systems. F. recreational facilities. G. installed and free-standing kitchen and laundry appliances not listed in Section 10.1.F. H. appliance thermostats including their calibration, adequacy of heating elements, self cleaning oven cycles, indicator lights, door seals, timers, clocks, timed features, and other specialized features of the appliance. I. operate, or confirm the operation of every control and feature of an inspected appliance.
Door binds at the top, unable to fully close the door. Recommend trimming or sanding down top of the door.
Here is a helpful DIY article on how to fix a sticking door.
IN | NI | NP | O | ||
---|---|---|---|---|---|
12.1 | Garbage Disposal | X | |||
12.2 | Dishwasher | X | |||
12.3 | Refrigerator | X | |||
12.4 | Range/Oven/Cooktop | X | |||
12.5 | Microwave Oven | X |
10.1 The inspector shall inspect: F. installed ovens, ranges, surface cooking appliances, microwave ovens, dishwashing machines, and food waste grinders by using normal operating controls to activate the primary function. 10.2 The inspector is NOT required to inspect: G. installed and free-standing kitchen and laundry appliances not listed in Section 10.1.F. H. appliance thermostats including their calibration, adequacy of heating elements, self cleaning oven cycles, indicator lights, door seals, timers, clocks, timed features, and other specialized features of the appliance. I. operate, or con rm the operation of every control and feature of an inspected appliance.
IN | NI | NP | O | ||
---|---|---|---|---|---|
13.1 | Fireplaces, Stoves & Inserts | X | |||
13.2 | Chimney & Vent Systems | X | |||
13.3 | Fuel-burning Accessories | X |
12.1 The inspector shall: A. inspect: 1. fuel-burning replaces, stoves, and replace inserts. 2. fuel-burning accessories installed in fireplaces. 3. chimneys and vent systems. B. describe systems and components listed in 12.1.A.1 and .2. 12.2 The inspector is NOT required to: A. inspect: 1. interiors of vent systems, uses, and chimneys that are not readily accessible. 2. fire screens and doors. 3. seals and gaskets. 4. automatic fuel feed devices. 5. mantles and replace surrounds. 6. combustion air components and to determine their adequacy. 7. heat distribution assists (gravity fed and fan assisted). 8. fuel-burning replaces and appliances located outside the inspected structures. B. determine draft characteristics. C. move fireplace inserts and stoves or firebox contents.